From 4746e2cd0e183314cfb362383c2b4555ebd2b49e Mon Sep 17 00:00:00 2001
From: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Date: Wed, 3 Dec 2025 11:37:12 +0800
Subject: [PATCH 01/19] Bluetooth: hci_qca: Fix SSR (SubSystem Restart) fail
 when BT_EN is pulled up by hw

On QCS9075 and QCA8275 platforms, the BT_EN pin is always pulled up by hw
and cannot be controlled by the host. As a result, in case of a firmware
crash, the host cannot trigger a cold reset. Instead, the BT controller
performs a warm restart on its own, without reloading the firmware.

This leads to the controller remaining in IBS_WAKE state, while the host
expects it to be in sleep mode. The mismatch causes HCI reset commands
to time out. Additionally, the driver does not clear internal flags
QCA_SSR_TRIGGERED and QCA_IBS_DISABLED, which blocks the reset sequence.
If the SSR duration exceeds 2 seconds, the host may enter TX sleep mode
due to tx_idle_timeout, further preventing recovery. Also, memcoredump_flag
is not cleared, so only the first SSR generates a coredump.

Tell the driver that the BT controller has undergone a proper restart sequence:

- Clear QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags after SSR.
- Add a 50ms delay to allow the controller to complete its warm reset.
- Reset tx_idle_timer to prevent the host from entering TX sleep mode.
- Clear memcoredump_flag to allow multiple coredump captures.

Apply these steps only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set,
which indicates that BT_EN is defined in DTS and cannot be toggled.

Refer to the comment in include/net/bluetooth/hci.h for details on
HCI_QUIRK_NON_PERSISTENT_SETUP.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/hci_qca.c | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 888176b0faa90..a3c217571c3c4 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -1653,6 +1653,39 @@ static void qca_hw_error(struct hci_dev *hdev, u8 code)
 		skb_queue_purge(&qca->rx_memdump_q);
 	}
 
+	/*
+	 * If the BT chip's bt_en pin is connected to a 3.3V power supply via
+	 * hardware and always stays high, driver cannot control the bt_en pin.
+	 * As a result, during SSR (SubSystem Restart), QCA_SSR_TRIGGERED and
+	 * QCA_IBS_DISABLED flags cannot be cleared, which leads to a reset
+	 * command timeout.
+	 * Add an msleep delay to ensure controller completes the SSR process.
+	 *
+	 * Host will not download the firmware after SSR, controller to remain
+	 * in the IBS_WAKE state, and the host needs to synchronize with it
+	 *
+	 * Since the bluetooth chip has been reset, clear the memdump state.
+	 */
+	if (!hci_test_quirk(hu->hdev, HCI_QUIRK_NON_PERSISTENT_SETUP)) {
+		/*
+		 * When the SSR (SubSystem Restart) duration exceeds 2 seconds,
+		 * it triggers host tx_idle_delay, which sets host TX state
+		 * to sleep. Reset tx_idle_timer after SSR to prevent
+		 * host enter TX IBS_Sleep mode.
+		 */
+		mod_timer(&qca->tx_idle_timer, jiffies +
+				  msecs_to_jiffies(qca->tx_idle_delay));
+
+		/* Controller reset completion time is 50ms */
+		msleep(50);
+
+		clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
+		clear_bit(QCA_IBS_DISABLED, &qca->flags);
+
+		qca->tx_ibs_state = HCI_IBS_TX_AWAKE;
+		qca->memdump_state = QCA_MEMDUMP_IDLE;
+	}
+
 	clear_bit(QCA_HW_ERROR_EVENT, &qca->flags);
 }
 

From 3d55304c6e437fe5e7fc02a3b7966d928bbb0b83 Mon Sep 17 00:00:00 2001
From: Pauli Virtanen <pav@iki.fi>
Date: Thu, 4 Dec 2025 22:40:20 +0200
Subject: [PATCH 02/19] Bluetooth: MGMT: report BIS capability flags in
 supported settings

MGMT_SETTING_ISO_BROADCASTER and MGMT_SETTING_ISO_RECEIVER flags are
missing from supported_settings although they are in current_settings.

Report them also in supported_settings to be consistent.

Fixes: ae7533613133 ("Bluetooth: Check for ISO support in controller")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 net/bluetooth/mgmt.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/net/bluetooth/mgmt.c b/net/bluetooth/mgmt.c
index c11cdef42b6f6..5be9b8c919490 100644
--- a/net/bluetooth/mgmt.c
+++ b/net/bluetooth/mgmt.c
@@ -849,6 +849,12 @@ static u32 get_supported_settings(struct hci_dev *hdev)
 	if (cis_peripheral_capable(hdev))
 		settings |= MGMT_SETTING_CIS_PERIPHERAL;
 
+	if (bis_capable(hdev))
+		settings |= MGMT_SETTING_ISO_BROADCASTER;
+
+	if (sync_recv_capable(hdev))
+		settings |= MGMT_SETTING_ISO_SYNC_RECEIVER;
+
 	if (ll_privacy_capable(hdev))
 		settings |= MGMT_SETTING_LL_PRIVACY;
 

From 9b10de4acec0db65e2f3139c4b6a3e664a46dd24 Mon Sep 17 00:00:00 2001
From: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Date: Wed, 10 Dec 2025 11:38:08 -0500
Subject: [PATCH 03/19] Bluetooth: hci_conn: Fix using conn->le_{tx,rx}_phy as
 supported PHYs

conn->le_{tx,rx}_phy is not actually a bitfield as it set by
HCI_EV_LE_PHY_UPDATE_COMPLETE it is actually correspond to the current
PHY in use not what is supported by the controller, so this introduces
different fields (conn->le_{tx,rx}_def_phys) to track what PHYs are
supported by the connection.

Fixes: eab2404ba798 ("Bluetooth: Add BT_PHY socket option")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 include/net/bluetooth/hci_core.h |  2 ++
 net/bluetooth/hci_conn.c         | 17 +++++++++++------
 net/bluetooth/hci_event.c        | 30 +++++++++++++++++++++++++++---
 3 files changed, 40 insertions(+), 9 deletions(-)

diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
index 4263e71a23efb..8aadf4cdead2b 100644
--- a/include/net/bluetooth/hci_core.h
+++ b/include/net/bluetooth/hci_core.h
@@ -730,6 +730,8 @@ struct hci_conn {
 	__u16		le_per_adv_data_offset;
 	__u8		le_adv_phy;
 	__u8		le_adv_sec_phy;
+	__u8		le_tx_def_phys;
+	__u8		le_rx_def_phys;
 	__u8		le_tx_phy;
 	__u8		le_rx_phy;
 	__s8		rssi;
diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
index c3f7828bf9d54..5a4374ccf8e84 100644
--- a/net/bluetooth/hci_conn.c
+++ b/net/bluetooth/hci_conn.c
@@ -1008,6 +1008,11 @@ static struct hci_conn *__hci_conn_add(struct hci_dev *hdev, int type,
 		/* conn->src should reflect the local identity address */
 		hci_copy_identity_address(hdev, &conn->src, &conn->src_type);
 		conn->mtu = hdev->le_mtu ? hdev->le_mtu : hdev->acl_mtu;
+		/* Use the controller supported PHYS as default until the
+		 * remote features are resolved.
+		 */
+		conn->le_tx_def_phys = hdev->le_tx_def_phys;
+		conn->le_rx_def_phys = hdev->le_tx_def_phys;
 		break;
 	case CIS_LINK:
 		/* conn->src should reflect the local identity address */
@@ -2928,22 +2933,22 @@ u32 hci_conn_get_phy(struct hci_conn *conn)
 		break;
 
 	case LE_LINK:
-		if (conn->le_tx_phy & HCI_LE_SET_PHY_1M)
+		if (conn->le_tx_def_phys & HCI_LE_SET_PHY_1M)
 			phys |= BT_PHY_LE_1M_TX;
 
-		if (conn->le_rx_phy & HCI_LE_SET_PHY_1M)
+		if (conn->le_rx_def_phys & HCI_LE_SET_PHY_1M)
 			phys |= BT_PHY_LE_1M_RX;
 
-		if (conn->le_tx_phy & HCI_LE_SET_PHY_2M)
+		if (conn->le_tx_def_phys & HCI_LE_SET_PHY_2M)
 			phys |= BT_PHY_LE_2M_TX;
 
-		if (conn->le_rx_phy & HCI_LE_SET_PHY_2M)
+		if (conn->le_rx_def_phys & HCI_LE_SET_PHY_2M)
 			phys |= BT_PHY_LE_2M_RX;
 
-		if (conn->le_tx_phy & HCI_LE_SET_PHY_CODED)
+		if (conn->le_tx_def_phys & HCI_LE_SET_PHY_CODED)
 			phys |= BT_PHY_LE_CODED_TX;
 
-		if (conn->le_rx_phy & HCI_LE_SET_PHY_CODED)
+		if (conn->le_rx_def_phys & HCI_LE_SET_PHY_CODED)
 			phys |= BT_PHY_LE_CODED_RX;
 
 		break;
diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index a9868f17ef40f..58075bf720554 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -6607,8 +6607,20 @@ static void hci_le_remote_feat_complete_evt(struct hci_dev *hdev, void *data,
 
 	conn = hci_conn_hash_lookup_handle(hdev, __le16_to_cpu(ev->handle));
 	if (conn) {
-		if (!ev->status)
-			memcpy(conn->features[0], ev->features, 8);
+		if (!ev->status) {
+			memcpy(conn->le_features, ev->features, 8);
+
+			/* Update supported PHYs */
+			if (!(conn->le_features[1] & HCI_LE_PHY_2M)) {
+				conn->le_tx_def_phys &= ~HCI_LE_SET_PHY_2M;
+				conn->le_rx_def_phys &= ~HCI_LE_SET_PHY_2M;
+			}
+
+			if (!(conn->le_features[1] & HCI_LE_PHY_CODED)) {
+				conn->le_tx_def_phys &= ~HCI_LE_SET_PHY_CODED;
+				conn->le_rx_def_phys &= ~HCI_LE_SET_PHY_CODED;
+			}
+		}
 
 		if (conn->state == BT_CONFIG) {
 			__u8 status;
@@ -7221,9 +7233,21 @@ static void hci_le_read_all_remote_features_evt(struct hci_dev *hdev,
 	if (!conn)
 		goto unlock;
 
-	if (!ev->status)
+	if (!ev->status) {
 		memcpy(conn->le_features, ev->features, 248);
 
+		/* Update supported PHYs */
+		if (!(conn->le_features[1] & HCI_LE_PHY_2M)) {
+			conn->le_tx_def_phys &= ~HCI_LE_SET_PHY_2M;
+			conn->le_rx_def_phys &= ~HCI_LE_SET_PHY_2M;
+		}
+
+		if (!(conn->le_features[1] & HCI_LE_PHY_CODED)) {
+			conn->le_tx_def_phys &= ~HCI_LE_SET_PHY_CODED;
+			conn->le_rx_def_phys &= ~HCI_LE_SET_PHY_CODED;
+		}
+	}
+
 	if (conn->state == BT_CONFIG) {
 		__u8 status;
 

From 3a7cf69ce3cfce597357cb677a4f23e0d26481a3 Mon Sep 17 00:00:00 2001
From: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Date: Wed, 10 Dec 2025 11:02:28 -0500
Subject: [PATCH 04/19] Bluetooth: btusb: revert use of devm_kzalloc in btusb

This reverts commit 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in
btusb.c file").

In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This
ties the lifetime of all the btusb data to the binding of a driver to
one interface, INTF. In a driver that binds to other interfaces, ISOC
and DIAG, this is an accident waiting to happen.

The issue is revealed in btusb_disconnect(), where calling
usb_driver_release_interface(&btusb_driver, data->intf) will have devm
free the data that is also being used by the other interfaces of the
driver that may not be released yet.

To fix this, revert the use of devm and go back to freeing memory
explicitly.

Fixes: 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in btusb.c file")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/btusb.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 8ed3883ab8eef..ded09e94d296d 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -4052,7 +4052,7 @@ static int btusb_probe(struct usb_interface *intf,
 			return -ENODEV;
 	}
 
-	data = devm_kzalloc(&intf->dev, sizeof(*data), GFP_KERNEL);
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 
@@ -4075,8 +4075,10 @@ static int btusb_probe(struct usb_interface *intf,
 		}
 	}
 
-	if (!data->intr_ep || !data->bulk_tx_ep || !data->bulk_rx_ep)
+	if (!data->intr_ep || !data->bulk_tx_ep || !data->bulk_rx_ep) {
+		kfree(data);
 		return -ENODEV;
+	}
 
 	if (id->driver_info & BTUSB_AMP) {
 		data->cmdreq_type = USB_TYPE_CLASS | 0x01;
@@ -4131,8 +4133,10 @@ static int btusb_probe(struct usb_interface *intf,
 	data->recv_acl = hci_recv_frame;
 
 	hdev = hci_alloc_dev_priv(priv_size);
-	if (!hdev)
+	if (!hdev) {
+		kfree(data);
 		return -ENOMEM;
+	}
 
 	hdev->bus = HCI_USB;
 	hci_set_drvdata(hdev, data);
@@ -4406,6 +4410,7 @@ static int btusb_probe(struct usb_interface *intf,
 	if (data->reset_gpio)
 		gpiod_put(data->reset_gpio);
 	hci_free_dev(hdev);
+	kfree(data);
 	return err;
 }
 
@@ -4454,6 +4459,7 @@ static void btusb_disconnect(struct usb_interface *intf)
 	}
 
 	hci_free_dev(hdev);
+	kfree(data);
 }
 
 #ifdef CONFIG_PM

From b96a6fd8cb4ec10aff6d3beadf558c53f2bedbc1 Mon Sep 17 00:00:00 2001
From: Bluecross <elantsew.andrew@gmail.com>
Date: Wed, 10 Dec 2025 23:22:25 +0300
Subject: [PATCH 05/19] Bluetooth: btusb: Add support for MediaTek7920
 0489:e158

Add support for MediaTek7920 0489:e158

/sys/kernel/debug/usb/devices reports for that device:

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e158 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Signed-off-by: Andrew Elatsev <elantsew.andrew@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index ded09e94d296d..646de80c7e7be 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -637,6 +637,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x13d3, 0x3622), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe158), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH },
 
 	/* Additional MediaTek MT7921 Bluetooth devices */
 	{ USB_DEVICE(0x0489, 0xe0c8), .driver_info = BTUSB_MEDIATEK |

From 0ad59c87f41cfd10f9e686f8a076e927c5f2288f Mon Sep 17 00:00:00 2001
From: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Date: Wed, 10 Dec 2025 23:21:09 +0000
Subject: [PATCH 06/19] Bluetooth: hci_bcm4377: Use generic power management

Switch to the generic PCI power management framework and remove legacy
callbacks like .suspend() and .resume(). With the generic framework, the
standard PCI related work like:
        - pci_save/restore_state()
        - pci_enable/disable_device()
        - pci_set_power_state()
is handled by the PCI core and this driver should implement only
hci_bcm4377 specific operations in its respective callback functions.

Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/hci_bcm4377.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/bluetooth/hci_bcm4377.c b/drivers/bluetooth/hci_bcm4377.c
index 45e6d84224ee3..925d0a6359453 100644
--- a/drivers/bluetooth/hci_bcm4377.c
+++ b/drivers/bluetooth/hci_bcm4377.c
@@ -2416,8 +2416,9 @@ static int bcm4377_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 					hdev);
 }
 
-static int bcm4377_suspend(struct pci_dev *pdev, pm_message_t state)
+static int bcm4377_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct bcm4377_data *bcm4377 = pci_get_drvdata(pdev);
 	int ret;
 
@@ -2431,8 +2432,9 @@ static int bcm4377_suspend(struct pci_dev *pdev, pm_message_t state)
 	return 0;
 }
 
-static int bcm4377_resume(struct pci_dev *pdev)
+static int bcm4377_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct bcm4377_data *bcm4377 = pci_get_drvdata(pdev);
 
 	iowrite32(BCM4377_BAR0_SLEEP_CONTROL_UNQUIESCE,
@@ -2441,6 +2443,8 @@ static int bcm4377_resume(struct pci_dev *pdev)
 	return hci_resume_dev(bcm4377->hdev);
 }
 
+static DEFINE_SIMPLE_DEV_PM_OPS(bcm4377_ops, bcm4377_suspend, bcm4377_resume);
+
 static const struct dmi_system_id bcm4377_dmi_board_table[] = {
 	{
 		.matches = {
@@ -2541,8 +2545,7 @@ static struct pci_driver bcm4377_pci_driver = {
 	.name = "hci_bcm4377",
 	.id_table = bcm4377_devid_table,
 	.probe = bcm4377_probe,
-	.suspend = bcm4377_suspend,
-	.resume = bcm4377_resume,
+	.driver.pm = &bcm4377_ops,
 };
 module_pci_driver(bcm4377_pci_driver);
 

From fd52b1d0ad7de69b1266c2efa7065e1d2f8acb49 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= <u.kleine-koenig@baylibre.com>
Date: Wed, 17 Dec 2025 12:20:33 +0100
Subject: [PATCH 07/19] Bluetooth: btmtksdio: Use pm_ptr instead of #ifdef
 CONFIG_PM
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

This increases build coverage and allows to drop an #ifdef.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/btmtksdio.c | 8 +-------
 1 file changed, 1 insertion(+), 7 deletions(-)

diff --git a/drivers/bluetooth/btmtksdio.c b/drivers/bluetooth/btmtksdio.c
index fba3ab6d30a5a..e986e5af51ae1 100644
--- a/drivers/bluetooth/btmtksdio.c
+++ b/drivers/bluetooth/btmtksdio.c
@@ -1472,7 +1472,6 @@ static void btmtksdio_remove(struct sdio_func *func)
 	hci_free_dev(hdev);
 }
 
-#ifdef CONFIG_PM
 static int btmtksdio_runtime_suspend(struct device *dev)
 {
 	struct sdio_func *func = dev_to_sdio_func(dev);
@@ -1542,18 +1541,13 @@ static const struct dev_pm_ops btmtksdio_pm_ops = {
 	RUNTIME_PM_OPS(btmtksdio_runtime_suspend, btmtksdio_runtime_resume, NULL)
 };
 
-#define BTMTKSDIO_PM_OPS (&btmtksdio_pm_ops)
-#else	/* CONFIG_PM */
-#define BTMTKSDIO_PM_OPS NULL
-#endif	/* CONFIG_PM */
-
 static struct sdio_driver btmtksdio_driver = {
 	.name		= "btmtksdio",
 	.probe		= btmtksdio_probe,
 	.remove		= btmtksdio_remove,
 	.id_table	= btmtksdio_table,
 	.drv = {
-		.pm = BTMTKSDIO_PM_OPS,
+		.pm = pm_ptr(&btmtksdio_pm_ops),
 	}
 };
 

From ad2804ccc724fa12a5497d4ec04aa5fc3183fa6e Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Stefan=20S=C3=B8rensen?= <ssorensen@roku.com>
Date: Tue, 16 Dec 2025 10:20:09 +0100
Subject: [PATCH 08/19] Bluetooth: hci_conn: use mod_delayed_work for active
 mode timeout
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

hci_conn_enter_active_mode() uses queue_delayed_work() with the
intention that the work will run after the given timeout. However,
queue_delayed_work() does nothing if the work is already queued, so
depending on the link policy we may end up putting the connection
into idle mode every hdev->idle_timeout ms.

Use mod_delayed_work() instead so the work is queued if not already
queued, and the timeout is updated otherwise.

Signed-off-by: Stefan Sørensen <ssorensen@roku.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 net/bluetooth/hci_conn.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
index 5a4374ccf8e84..1b98b64674854 100644
--- a/net/bluetooth/hci_conn.c
+++ b/net/bluetooth/hci_conn.c
@@ -2619,8 +2619,8 @@ void hci_conn_enter_active_mode(struct hci_conn *conn, __u8 force_active)
 
 timer:
 	if (hdev->idle_timeout > 0)
-		queue_delayed_work(hdev->workqueue, &conn->idle_work,
-				   msecs_to_jiffies(hdev->idle_timeout));
+		mod_delayed_work(hdev->workqueue, &conn->idle_work,
+				 msecs_to_jiffies(hdev->idle_timeout));
 }
 
 /* Drop all connection on the device */

From f7f2402b780738ff4bdb2f8d40a6c2136f1f92d4 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Stefan=20S=C3=B8rensen?= <ssorensen@roku.com>
Date: Tue, 16 Dec 2025 10:20:10 +0100
Subject: [PATCH 09/19] Bluetooth: hci_conn: Set link_policy on incoming ACL
 connections
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

The connection link policy is only set when establishing an outgoing
ACL connection causing connection idle modes not to be available on
incoming connections. Move the setting of the link policy to the
creation of the connection so all ACL connection will use the link
policy set on the HCI device.

Signed-off-by: Stefan Sørensen <ssorensen@roku.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 net/bluetooth/hci_conn.c | 1 +
 net/bluetooth/hci_sync.c | 2 --
 2 files changed, 1 insertion(+), 2 deletions(-)

diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
index 1b98b64674854..dc085856f5e91 100644
--- a/net/bluetooth/hci_conn.c
+++ b/net/bluetooth/hci_conn.c
@@ -1002,6 +1002,7 @@ static struct hci_conn *__hci_conn_add(struct hci_dev *hdev, int type,
 	switch (type) {
 	case ACL_LINK:
 		conn->pkt_type = hdev->pkt_type & ACL_PTYPE_MASK;
+		conn->link_policy = hdev->link_policy;
 		conn->mtu = hdev->acl_mtu;
 		break;
 	case LE_LINK:
diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
index a9f5b1a68356e..3b620c6eed70c 100644
--- a/net/bluetooth/hci_sync.c
+++ b/net/bluetooth/hci_sync.c
@@ -6896,8 +6896,6 @@ static int hci_acl_create_conn_sync(struct hci_dev *hdev, void *data)
 
 	conn->attempt++;
 
-	conn->link_policy = hdev->link_policy;
-
 	memset(&cp, 0, sizeof(cp));
 	bacpy(&cp.bdaddr, &conn->dst);
 	cp.pscan_rep_mode = 0x02;

From fa10d5a2b8f9dc31f390c16bf611fb8171f52707 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Stefan=20S=C3=B8rensen?= <ssorensen@roku.com>
Date: Tue, 16 Dec 2025 10:20:11 +0100
Subject: [PATCH 10/19] Bluetooth: mgmt: Add idle_timeout to configurable
 system parameters
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

While the configurable system parameters allow controlling the SNIFF
mode parameters, they do not include the idle_timeout parameter
responsible for enabling SNIFF mode.

Add the idle_timeout parameter to allow controlling the idle timeout
of BR/EDR connections.

Signed-off-by: Stefan Sørensen <ssorensen@roku.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 net/bluetooth/mgmt_config.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/net/bluetooth/mgmt_config.c b/net/bluetooth/mgmt_config.c
index c4063d200c0a6..fdcc752c6f13f 100644
--- a/net/bluetooth/mgmt_config.c
+++ b/net/bluetooth/mgmt_config.c
@@ -11,6 +11,12 @@
 #include "mgmt_util.h"
 #include "mgmt_config.h"
 
+#define HDEV_PARAM_U32(_param_name_) \
+	struct {\
+		struct mgmt_tlv_hdr entry; \
+		__le32 value; \
+	} __packed _param_name_
+
 #define HDEV_PARAM_U16(_param_name_) \
 	struct {\
 		struct mgmt_tlv_hdr entry; \
@@ -29,6 +35,12 @@
 		cpu_to_le16(hdev->_param_name_) \
 	}
 
+#define TLV_SET_U32(_param_code_, _param_name_) \
+	{ \
+		{ cpu_to_le16(_param_code_), sizeof(__u32) }, \
+		cpu_to_le32(hdev->_param_name_) \
+	}
+
 #define TLV_SET_U8(_param_code_, _param_name_) \
 	{ \
 		{ cpu_to_le16(_param_code_), sizeof(__u8) }, \
@@ -78,6 +90,7 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,
 		HDEV_PARAM_U16(advmon_allowlist_duration);
 		HDEV_PARAM_U16(advmon_no_filter_duration);
 		HDEV_PARAM_U8(enable_advmon_interleave_scan);
+		HDEV_PARAM_U32(idle_timeout);
 	} __packed rp = {
 		TLV_SET_U16(0x0000, def_page_scan_type),
 		TLV_SET_U16(0x0001, def_page_scan_int),
@@ -111,6 +124,7 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,
 		TLV_SET_U16(0x001d, advmon_allowlist_duration),
 		TLV_SET_U16(0x001e, advmon_no_filter_duration),
 		TLV_SET_U8(0x001f, enable_advmon_interleave_scan),
+		TLV_SET_U32(0x0020, idle_timeout),
 	};
 
 	bt_dev_dbg(hdev, "sock %p", sk);
@@ -122,6 +136,7 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,
 }
 
 #define TO_TLV(x)		((struct mgmt_tlv *)(x))
+#define TLV_GET_LE32(tlv)	le32_to_cpu(*((__le32 *)(TO_TLV(tlv)->value)))
 #define TLV_GET_LE16(tlv)	le16_to_cpu(*((__le16 *)(TO_TLV(tlv)->value)))
 #define TLV_GET_U8(tlv)		(*((__u8 *)(TO_TLV(tlv)->value)))
 
@@ -191,6 +206,9 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,
 		case 0x001f:
 			exp_type_len = sizeof(u8);
 			break;
+		case 0x0020:
+			exp_type_len = sizeof(u32);
+			break;
 		default:
 			exp_type_len = 0;
 			bt_dev_warn(hdev, "unsupported parameter %u", type);
@@ -314,6 +332,9 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,
 		case 0x0001f:
 			hdev->enable_advmon_interleave_scan = TLV_GET_U8(buffer);
 			break;
+		case 0x00020:
+			hdev->idle_timeout = TLV_GET_LE32(buffer);
+			break;
 		default:
 			bt_dev_warn(hdev, "unsupported parameter %u", type);
 			break;

From d02dfc95df003dcbcd74f695433eae63b50b80ca Mon Sep 17 00:00:00 2001
From: Naga Bhavani Akella <naga.akella@oss.qualcomm.com>
Date: Wed, 17 Dec 2025 16:55:23 +0530
Subject: [PATCH 11/19] Bluetooth: hci_sync: Add LE Channel Sounding HCI
 Command/event structures

1. Implement LE Event Mask to include events required for
   LE Channel Sounding
2. Enable Channel Sounding feature bit in the
   LE Host Supported Features command
3. Define HCI command and event structures necessary for
   LE Channel Sounding functionality

Signed-off-by: Naga Bhavani Akella <naga.akella@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 include/net/bluetooth/hci.h      | 323 +++++++++++++++++++++++++++++++
 include/net/bluetooth/hci_core.h |   6 +
 net/bluetooth/hci_sync.c         |  45 ++++-
 3 files changed, 367 insertions(+), 7 deletions(-)

diff --git a/include/net/bluetooth/hci.h b/include/net/bluetooth/hci.h
index a27cd3626b872..4a731e1bec53b 100644
--- a/include/net/bluetooth/hci.h
+++ b/include/net/bluetooth/hci.h
@@ -654,6 +654,8 @@ enum {
 #define HCI_LE_ISO_BROADCASTER		0x40
 #define HCI_LE_ISO_SYNC_RECEIVER	0x80
 #define HCI_LE_LL_EXT_FEATURE		0x80
+#define HCI_LE_CS			0x40
+#define HCI_LE_CS_HOST			0x80
 
 /* Connection modes */
 #define HCI_CM_ACTIVE	0x0000
@@ -2269,6 +2271,204 @@ struct hci_cp_le_read_all_remote_features {
 	__u8	 pages;
 } __packed;
 
+/* Channel Sounding Commands */
+#define HCI_OP_LE_CS_RD_LOCAL_SUPP_CAP	0x2089
+struct hci_rp_le_cs_rd_local_supp_cap {
+	__u8	status;
+	__u8	num_config_supported;
+	__le16	max_consecutive_procedures_supported;
+	__u8	num_antennas_supported;
+	__u8	max_antenna_paths_supported;
+	__u8	roles_supported;
+	__u8	modes_supported;
+	__u8	rtt_capability;
+	__u8	rtt_aa_only_n;
+	__u8	rtt_sounding_n;
+	__u8	rtt_random_payload_n;
+	__le16	nadm_sounding_capability;
+	__le16	nadm_random_capability;
+	__u8	cs_sync_phys_supported;
+	__le16	subfeatures_supported;
+	__le16	t_ip1_times_supported;
+	__le16	t_ip2_times_supported;
+	__le16	t_fcs_times_supported;
+	__le16	t_pm_times_supported;
+	__u8	t_sw_time_supported;
+	__u8	tx_snr_capability;
+} __packed;
+
+#define HCI_OP_LE_CS_RD_RMT_SUPP_CAP		0x208A
+struct hci_cp_le_cs_rd_local_supp_cap {
+	__le16	handle;
+} __packed;
+
+#define HCI_OP_LE_CS_WR_CACHED_RMT_SUPP_CAP	0x208B
+struct hci_cp_le_cs_wr_cached_rmt_supp_cap {
+	__le16	handle;
+	__u8	num_config_supported;
+	__le16	max_consecutive_procedures_supported;
+	__u8	num_antennas_supported;
+	__u8	max_antenna_paths_supported;
+	__u8	roles_supported;
+	__u8	modes_supported;
+	__u8	rtt_capability;
+	__u8	rtt_aa_only_n;
+	__u8	rtt_sounding_n;
+	__u8	rtt_random_payload_n;
+	__le16	nadm_sounding_capability;
+	__le16	nadm_random_capability;
+	__u8	cs_sync_phys_supported;
+	__le16	subfeatures_supported;
+	__le16	t_ip1_times_supported;
+	__le16	t_ip2_times_supported;
+	__le16	t_fcs_times_supported;
+	__le16	t_pm_times_supported;
+	__u8	t_sw_time_supported;
+	__u8	tx_snr_capability;
+} __packed;
+
+struct hci_rp_le_cs_wr_cached_rmt_supp_cap {
+	__u8	status;
+	__le16	handle;
+} __packed;
+
+#define HCI_OP_LE_CS_SEC_ENABLE			0x208C
+struct hci_cp_le_cs_sec_enable {
+	__le16	handle;
+} __packed;
+
+#define HCI_OP_LE_CS_SET_DEFAULT_SETTINGS	0x208D
+struct hci_cp_le_cs_set_default_settings {
+	__le16	handle;
+	__u8	role_enable;
+	__u8	cs_sync_ant_sel;
+	__s8	max_tx_power;
+} __packed;
+
+struct hci_rp_le_cs_set_default_settings {
+	__u8	status;
+	__le16	handle;
+} __packed;
+
+#define HCI_OP_LE_CS_RD_RMT_FAE_TABLE		0x208E
+struct hci_cp_le_cs_rd_rmt_fae_table {
+	__le16	handle;
+} __packed;
+
+#define HCI_OP_LE_CS_WR_CACHED_RMT_FAE_TABLE	0x208F
+struct hci_cp_le_cs_wr_rmt_cached_fae_table {
+	__le16	handle;
+	__u8	remote_fae_table[72];
+} __packed;
+
+struct hci_rp_le_cs_wr_rmt_cached_fae_table {
+	__u8	status;
+	__le16	handle;
+} __packed;
+
+#define HCI_OP_LE_CS_CREATE_CONFIG		0x2090
+struct hci_cp_le_cs_create_config {
+	__le16	handle;
+	__u8	config_id;
+	__u8	create_context;
+	__u8	main_mode_type;
+	__u8	sub_mode_type;
+	__u8	min_main_mode_steps;
+	__u8	max_main_mode_steps;
+	__u8	main_mode_repetition;
+	__u8	mode_0_steps;
+	__u8	role;
+	__u8	rtt_type;
+	__u8	cs_sync_phy;
+	__u8	channel_map[10];
+	__u8	channel_map_repetition;
+	__u8	channel_selection_type;
+	__u8	ch3c_shape;
+	__u8	ch3c_jump;
+	__u8	reserved;
+} __packed;
+
+#define HCI_OP_LE_CS_REMOVE_CONFIG		0x2091
+struct hci_cp_le_cs_remove_config {
+	__le16	handle;
+	__u8	config_id;
+} __packed;
+
+#define HCI_OP_LE_CS_SET_CH_CLASSIFICATION	0x2092
+struct hci_cp_le_cs_set_ch_classification {
+	__u8	ch_classification[10];
+} __packed;
+
+struct hci_rp_le_cs_set_ch_classification {
+	__u8	status;
+} __packed;
+
+#define HCI_OP_LE_CS_SET_PROC_PARAM		0x2093
+struct hci_cp_le_cs_set_proc_param {
+	__le16	handle;
+	__u8	config_id;
+	__le16	max_procedure_len;
+	__le16	min_procedure_interval;
+	__le16	max_procedure_interval;
+	__le16	max_procedure_count;
+	__u8	min_subevent_len[3];
+	__u8	max_subevent_len[3];
+	__u8	tone_antenna_config_selection;
+	__u8	phy;
+	__u8	tx_power_delta;
+	__u8	preferred_peer_antenna;
+	__u8	snr_control_initiator;
+	__u8	snr_control_reflector;
+} __packed;
+
+struct hci_rp_le_cs_set_proc_param {
+	__u8	status;
+	__le16	handle;
+} __packed;
+
+#define HCI_OP_LE_CS_SET_PROC_ENABLE		0x2094
+struct hci_cp_le_cs_set_proc_enable {
+	__le16	handle;
+	__u8	config_id;
+	__u8	enable;
+} __packed;
+
+#define HCI_OP_LE_CS_TEST			0x2095
+struct hci_cp_le_cs_test {
+	__u8	main_mode_type;
+	__u8	sub_mode_type;
+	__u8	main_mode_repetition;
+	__u8	mode_0_steps;
+	__u8	role;
+	__u8	rtt_type;
+	__u8	cs_sync_phy;
+	__u8	cs_sync_antenna_selection;
+	__u8	subevent_len[3];
+	__le16	subevent_interval;
+	__u8	max_num_subevents;
+	__u8	transmit_power_level;
+	__u8	t_ip1_time;
+	__u8	t_ip2_time;
+	__u8	t_fcs_time;
+	__u8	t_pm_time;
+	__u8	t_sw_time;
+	__u8	tone_antenna_config_selection;
+	__u8	reserved;
+	__u8	snr_control_initiator;
+	__u8	snr_control_reflector;
+	__le16	drbg_nonce;
+	__u8	channel_map_repetition;
+	__le16	override_config;
+	__u8	override_parameters_length;
+	__u8	override_parameters_data[];
+} __packed;
+
+struct hci_rp_le_cs_test {
+	__u8	status;
+} __packed;
+
+#define HCI_OP_LE_CS_TEST_END			0x2096
+
 /* ---- HCI Events ---- */
 struct hci_ev_status {
 	__u8    status;
@@ -2960,6 +3160,129 @@ struct hci_evt_le_read_all_remote_features_complete {
 	__u8    features[248];
 } __packed;
 
+/* Channel Sounding Events */
+#define HCI_EVT_LE_CS_READ_RMT_SUPP_CAP_COMPLETE	0x2C
+struct hci_evt_le_cs_read_rmt_supp_cap_complete {
+	__u8	status;
+	__le16	handle;
+	__u8	num_configs_supp;
+	__le16	max_consec_proc_supp;
+	__u8	num_ant_supp;
+	__u8	max_ant_path_supp;
+	__u8	roles_supp;
+	__u8	modes_supp;
+	__u8	rtt_cap;
+	__u8	rtt_aa_only_n;
+	__u8	rtt_sounding_n;
+	__u8	rtt_rand_payload_n;
+	__le16	nadm_sounding_cap;
+	__le16	nadm_rand_cap;
+	__u8	cs_sync_phys_supp;
+	__le16	sub_feat_supp;
+	__le16	t_ip1_times_supp;
+	__le16	t_ip2_times_supp;
+	__le16	t_fcs_times_supp;
+	__le16	t_pm_times_supp;
+	__u8	t_sw_times_supp;
+	__u8	tx_snr_cap;
+} __packed;
+
+#define HCI_EVT_LE_CS_READ_RMT_FAE_TABLE_COMPLETE	0x2D
+struct hci_evt_le_cs_read_rmt_fae_table_complete {
+	__u8	status;
+	__le16	handle;
+	__u8	remote_fae_table[72];
+} __packed;
+
+#define HCI_EVT_LE_CS_SECURITY_ENABLE_COMPLETE		0x2E
+struct hci_evt_le_cs_security_enable_complete {
+	__u8	status;
+	__le16	handle;
+} __packed;
+
+#define HCI_EVT_LE_CS_CONFIG_COMPLETE			0x2F
+struct hci_evt_le_cs_config_complete {
+	__u8	status;
+	__le16	handle;
+	__u8	config_id;
+	__u8	action;
+	__u8	main_mode_type;
+	__u8	sub_mode_type;
+	__u8	min_main_mode_steps;
+	__u8	max_main_mode_steps;
+	__u8	main_mode_rep;
+	__u8	mode_0_steps;
+	__u8	role;
+	__u8	rtt_type;
+	__u8	cs_sync_phy;
+	__u8	channel_map[10];
+	__u8	channel_map_rep;
+	__u8	channel_sel_type;
+	__u8	ch3c_shape;
+	__u8	ch3c_jump;
+	__u8	reserved;
+	__u8	t_ip1_time;
+	__u8	t_ip2_time;
+	__u8	t_fcs_time;
+	__u8	t_pm_time;
+} __packed;
+
+#define HCI_EVT_LE_CS_PROCEDURE_ENABLE_COMPLETE		0x30
+struct hci_evt_le_cs_procedure_enable_complete {
+	__u8	status;
+	__le16	handle;
+	__u8	config_id;
+	__u8	state;
+	__u8	tone_ant_config_sel;
+	__s8	sel_tx_pwr;
+	__u8	sub_evt_len[3];
+	__u8	sub_evts_per_evt;
+	__le16	sub_evt_intrvl;
+	__le16	evt_intrvl;
+	__le16	proc_intrvl;
+	__le16	proc_counter;
+	__le16	max_proc_len;
+} __packed;
+
+#define HCI_EVT_LE_CS_SUBEVENT_RESULT			0x31
+struct hci_evt_le_cs_subevent_result {
+	__le16	handle;
+	__u8	config_id;
+	__le16	start_acl_conn_evt_counter;
+	__le16	proc_counter;
+	__le16	freq_comp;
+	__u8	ref_pwr_lvl;
+	__u8	proc_done_status;
+	__u8	subevt_done_status;
+	__u8	abort_reason;
+	__u8	num_ant_paths;
+	__u8	num_steps_reported;
+	__u8	step_mode[0]; /* depends on num_steps_reported */
+	__u8	step_channel[0]; /* depends on num_steps_reported */
+	__u8	step_data_length[0]; /* depends on num_steps_reported */
+	__u8	step_data[0]; /* depends on num_steps_reported */
+} __packed;
+
+#define HCI_EVT_LE_CS_SUBEVENT_RESULT_CONTINUE		0x32
+struct hci_evt_le_cs_subevent_result_continue {
+	__le16	handle;
+	__u8	config_id;
+	__u8	proc_done_status;
+	__u8	subevt_done_status;
+	__u8	abort_reason;
+	__u8	num_ant_paths;
+	__u8	num_steps_reported;
+	__u8	step_mode[0]; /* depends on num_steps_reported */
+	__u8	step_channel[0]; /* depends on num_steps_reported */
+	__u8	step_data_length[0]; /* depends on num_steps_reported */
+	__u8	step_data[0]; /* depends on num_steps_reported */
+} __packed;
+
+#define HCI_EVT_LE_CS_TEST_END_COMPLETE			0x33
+struct hci_evt_le_cs_test_end_complete {
+	__u8	status;
+} __packed;
+
 #define HCI_EV_VENDOR			0xff
 
 /* Internal events generated by Bluetooth stack */
diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
index 8aadf4cdead2b..a7d5beb01b695 100644
--- a/include/net/bluetooth/hci_core.h
+++ b/include/net/bluetooth/hci_core.h
@@ -2073,6 +2073,12 @@ void hci_conn_del_sysfs(struct hci_conn *conn);
 #define ll_ext_feature_capable(dev) \
 	((dev)->le_features[7] & HCI_LE_LL_EXT_FEATURE)
 
+/* Channel sounding support */
+#define le_cs_capable(dev) \
+	((dev)->le_features[5] & HCI_LE_CS)
+#define le_cs_host_capable(dev) \
+	((dev)->le_features[5] & HCI_LE_CS_HOST)
+
 #define mws_transport_config_capable(dev) (((dev)->commands[30] & 0x08) && \
 	(!hci_test_quirk((dev), HCI_QUIRK_BROKEN_MWS_TRANSPORT_CONFIG)))
 
diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
index 3b620c6eed70c..dd3f7bd98b1c6 100644
--- a/net/bluetooth/hci_sync.c
+++ b/net/bluetooth/hci_sync.c
@@ -4427,6 +4427,17 @@ static int hci_le_set_event_mask_sync(struct hci_dev *hdev)
 		events[4] |= 0x02;	/* LE BIG Info Advertising Report */
 	}
 
+	if (le_cs_capable(hdev)) {
+		/* Channel Sounding events */
+		events[5] |= 0x08;	/* LE CS Read Remote Supported Cap Complete event */
+		events[5] |= 0x10;	/* LE CS Read Remote FAE Table Complete event */
+		events[5] |= 0x20;	/* LE CS Security Enable Complete event */
+		events[5] |= 0x40;	/* LE CS Config Complete event */
+		events[5] |= 0x80;	/* LE CS Procedure Enable Complete event */
+		events[6] |= 0x01;	/* LE CS Subevent Result event */
+		events[6] |= 0x02;	/* LE CS Subevent Result Continue event */
+		events[6] |= 0x04;	/* LE CS Test End Complete event */
+	}
 	return __hci_cmd_sync_status(hdev, HCI_OP_LE_SET_EVENT_MASK,
 				     sizeof(events), events, HCI_CMD_TIMEOUT);
 }
@@ -4559,23 +4570,43 @@ static int hci_set_le_support_sync(struct hci_dev *hdev)
 }
 
 /* LE Set Host Feature */
-static int hci_le_set_host_feature_sync(struct hci_dev *hdev)
+static int hci_le_set_host_feature_sync(struct hci_dev *hdev, u8 bit, u8 value)
 {
 	struct hci_cp_le_set_host_feature cp;
 
-	if (!iso_capable(hdev))
-		return 0;
-
 	memset(&cp, 0, sizeof(cp));
 
 	/* Connected Isochronous Channels (Host Support) */
-	cp.bit_number = 32;
-	cp.bit_value = iso_enabled(hdev) ? 0x01 : 0x00;
+	cp.bit_number = bit;
+	cp.bit_value = value;
 
 	return __hci_cmd_sync_status(hdev, HCI_OP_LE_SET_HOST_FEATURE,
 				     sizeof(cp), &cp, HCI_CMD_TIMEOUT);
 }
 
+/* Set Host Features, each feature needs to be sent separately since
+ * HCI_OP_LE_SET_HOST_FEATURE doesn't support setting all of them at once.
+ */
+static int hci_le_set_host_features_sync(struct hci_dev *hdev)
+{
+	int err;
+
+	if (iso_capable(hdev)) {
+		/* Connected Isochronous Channels (Host Support) */
+		err = hci_le_set_host_feature_sync(hdev, 32,
+						   (iso_enabled(hdev) ? 0x01 :
+						    0x00));
+		if (err)
+			return err;
+	}
+
+	if (le_cs_capable(hdev))
+		/* Channel Sounding (Host Support) */
+		err = hci_le_set_host_feature_sync(hdev, 47, 0x01);
+
+	return err;
+}
+
 /* LE Controller init stage 3 command sequence */
 static const struct hci_init_stage le_init3[] = {
 	/* HCI_OP_LE_SET_EVENT_MASK */
@@ -4603,7 +4634,7 @@ static const struct hci_init_stage le_init3[] = {
 	/* HCI_OP_WRITE_LE_HOST_SUPPORTED */
 	HCI_INIT(hci_set_le_support_sync),
 	/* HCI_OP_LE_SET_HOST_FEATURE */
-	HCI_INIT(hci_le_set_host_feature_sync),
+	HCI_INIT(hci_le_set_host_features_sync),
 	{}
 };
 

From 1d7a8fd800eb96f1175ddc3517822900c382cb80 Mon Sep 17 00:00:00 2001
From: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Date: Wed, 17 Dec 2025 10:50:51 -0500
Subject: [PATCH 12/19] Bluetooth: L2CAP: Add support for setting BT_PHY

This enables client to use setsockopt(BT_PHY) to set the connection
packet type/PHY:

Example setting BT_PHY_BR_1M_1SLOT:

< HCI Command: Change Conne.. (0x01|0x000f) plen 4
        Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
        Packet type: 0x331e
          2-DH1 may not be used
          3-DH1 may not be used
          DM1 may be used
          DH1 may be used
          2-DH3 may not be used
          3-DH3 may not be used
          2-DH5 may not be used
          3-DH5 may not be used
> HCI Event: Command Status (0x0f) plen 4
      Change Connection Packet Type (0x01|0x000f) ncmd 1
        Status: Success (0x00)
> HCI Event: Connection Packet Typ.. (0x1d) plen 5
        Status: Success (0x00)
        Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
        Packet type: 0x331e
          2-DH1 may not be used
          3-DH1 may not be used
          DM1 may be used
          DH1 may be used
          2-DH3 may not be used
          3-DH3 may not be used
          2-DH5 may not be used

Example setting BT_PHY_LE_1M_TX and BT_PHY_LE_1M_RX:

< HCI Command: LE Set PHY (0x08|0x0032) plen 7
        Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
        All PHYs preference: 0x00
        TX PHYs preference: 0x01
          LE 1M
        RX PHYs preference: 0x01
          LE 1M
        PHY options preference: Reserved (0x0000)
> HCI Event: Command Status (0x0f) plen 4
      LE Set PHY (0x08|0x0032) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 6
      LE PHY Update Complete (0x0c)
        Status: Success (0x00)
        Handle: 1 Address: 00:AA:01:01:00:00 (Intel Corporation)
        TX PHY: LE 1M (0x01)
        RX PHY: LE 1M (0x01)

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 include/net/bluetooth/bluetooth.h |  39 ++++++-----
 include/net/bluetooth/hci.h       |   9 +++
 include/net/bluetooth/hci_core.h  |   1 +
 include/net/bluetooth/hci_sync.h  |   3 +
 net/bluetooth/hci_conn.c          | 105 ++++++++++++++++++++++++++++++
 net/bluetooth/hci_event.c         |  26 ++++++++
 net/bluetooth/hci_sync.c          |  72 ++++++++++++++++++++
 net/bluetooth/l2cap_sock.c        |  20 +++++-
 8 files changed, 259 insertions(+), 16 deletions(-)

diff --git a/include/net/bluetooth/bluetooth.h b/include/net/bluetooth/bluetooth.h
index d46ed9011ee5d..89a60919050b0 100644
--- a/include/net/bluetooth/bluetooth.h
+++ b/include/net/bluetooth/bluetooth.h
@@ -130,21 +130,30 @@ struct bt_voice {
 #define BT_RCVMTU		13
 #define BT_PHY			14
 
-#define BT_PHY_BR_1M_1SLOT	0x00000001
-#define BT_PHY_BR_1M_3SLOT	0x00000002
-#define BT_PHY_BR_1M_5SLOT	0x00000004
-#define BT_PHY_EDR_2M_1SLOT	0x00000008
-#define BT_PHY_EDR_2M_3SLOT	0x00000010
-#define BT_PHY_EDR_2M_5SLOT	0x00000020
-#define BT_PHY_EDR_3M_1SLOT	0x00000040
-#define BT_PHY_EDR_3M_3SLOT	0x00000080
-#define BT_PHY_EDR_3M_5SLOT	0x00000100
-#define BT_PHY_LE_1M_TX		0x00000200
-#define BT_PHY_LE_1M_RX		0x00000400
-#define BT_PHY_LE_2M_TX		0x00000800
-#define BT_PHY_LE_2M_RX		0x00001000
-#define BT_PHY_LE_CODED_TX	0x00002000
-#define BT_PHY_LE_CODED_RX	0x00004000
+#define BT_PHY_BR_1M_1SLOT	BIT(0)
+#define BT_PHY_BR_1M_3SLOT	BIT(1)
+#define BT_PHY_BR_1M_5SLOT	BIT(2)
+#define BT_PHY_EDR_2M_1SLOT	BIT(3)
+#define BT_PHY_EDR_2M_3SLOT	BIT(4)
+#define BT_PHY_EDR_2M_5SLOT	BIT(5)
+#define BT_PHY_EDR_3M_1SLOT	BIT(6)
+#define BT_PHY_EDR_3M_3SLOT	BIT(7)
+#define BT_PHY_EDR_3M_5SLOT	BIT(8)
+#define BT_PHY_LE_1M_TX		BIT(9)
+#define BT_PHY_LE_1M_RX		BIT(10)
+#define BT_PHY_LE_2M_TX		BIT(11)
+#define BT_PHY_LE_2M_RX		BIT(12)
+#define BT_PHY_LE_CODED_TX	BIT(13)
+#define BT_PHY_LE_CODED_RX	BIT(14)
+
+#define BT_PHY_BREDR_MASK	(BT_PHY_BR_1M_1SLOT | BT_PHY_BR_1M_3SLOT | \
+				 BT_PHY_BR_1M_5SLOT | BT_PHY_EDR_2M_1SLOT | \
+				 BT_PHY_EDR_2M_3SLOT | BT_PHY_EDR_2M_5SLOT | \
+				 BT_PHY_EDR_3M_1SLOT | BT_PHY_EDR_3M_3SLOT | \
+				 BT_PHY_EDR_3M_5SLOT)
+#define BT_PHY_LE_MASK		(BT_PHY_LE_1M_TX | BT_PHY_LE_1M_RX | \
+				 BT_PHY_LE_2M_TX | BT_PHY_LE_2M_RX | \
+				 BT_PHY_LE_CODED_TX | BT_PHY_LE_CODED_RX)
 
 #define BT_MODE			15
 
diff --git a/include/net/bluetooth/hci.h b/include/net/bluetooth/hci.h
index 4a731e1bec53b..db76c2d1eeaa1 100644
--- a/include/net/bluetooth/hci.h
+++ b/include/net/bluetooth/hci.h
@@ -1885,6 +1885,15 @@ struct hci_cp_le_set_default_phy {
 #define HCI_LE_SET_PHY_2M		0x02
 #define HCI_LE_SET_PHY_CODED		0x04
 
+#define HCI_OP_LE_SET_PHY		0x2032
+struct hci_cp_le_set_phy {
+	__le16  handle;
+	__u8    all_phys;
+	__u8    tx_phys;
+	__u8    rx_phys;
+	__le16   phy_opts;
+} __packed;
+
 #define HCI_OP_LE_SET_EXT_SCAN_PARAMS   0x2041
 struct hci_cp_le_set_ext_scan_params {
 	__u8    own_addr_type;
diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
index a7d5beb01b695..a7bffb908c1ec 100644
--- a/include/net/bluetooth/hci_core.h
+++ b/include/net/bluetooth/hci_core.h
@@ -2342,6 +2342,7 @@ void *hci_sent_cmd_data(struct hci_dev *hdev, __u16 opcode);
 void *hci_recv_event_data(struct hci_dev *hdev, __u8 event);
 
 u32 hci_conn_get_phy(struct hci_conn *conn);
+int hci_conn_set_phy(struct hci_conn *conn, u32 phys);
 
 /* ----- HCI Sockets ----- */
 void hci_send_to_sock(struct hci_dev *hdev, struct sk_buff *skb);
diff --git a/include/net/bluetooth/hci_sync.h b/include/net/bluetooth/hci_sync.h
index 56076bbc981d9..73e494b2591de 100644
--- a/include/net/bluetooth/hci_sync.h
+++ b/include/net/bluetooth/hci_sync.h
@@ -191,3 +191,6 @@ int hci_connect_big_sync(struct hci_dev *hdev, struct hci_conn *conn);
 int hci_past_sync(struct hci_conn *conn, struct hci_conn *le);
 
 int hci_le_read_remote_features(struct hci_conn *conn);
+
+int hci_acl_change_pkt_type(struct hci_conn *conn, u16 pkt_type);
+int hci_le_set_phy(struct hci_conn *conn, u8 tx_phys, u8 rx_phys);
diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
index dc085856f5e91..1a4b6badf2b35 100644
--- a/net/bluetooth/hci_conn.c
+++ b/net/bluetooth/hci_conn.c
@@ -2958,6 +2958,111 @@ u32 hci_conn_get_phy(struct hci_conn *conn)
 	return phys;
 }
 
+static u16 bt_phy_pkt_type(struct hci_conn *conn, u32 phys)
+{
+	u16 pkt_type = conn->pkt_type;
+
+	if (phys & BT_PHY_BR_1M_3SLOT)
+		pkt_type |= HCI_DM3 | HCI_DH3;
+	else
+		pkt_type &= ~(HCI_DM3 | HCI_DH3);
+
+	if (phys & BT_PHY_BR_1M_5SLOT)
+		pkt_type |= HCI_DM5 | HCI_DH5;
+	else
+		pkt_type &= ~(HCI_DM5 | HCI_DH5);
+
+	if (phys & BT_PHY_EDR_2M_1SLOT)
+		pkt_type &= ~HCI_2DH1;
+	else
+		pkt_type |= HCI_2DH1;
+
+	if (phys & BT_PHY_EDR_2M_3SLOT)
+		pkt_type &= ~HCI_2DH3;
+	else
+		pkt_type |= HCI_2DH3;
+
+	if (phys & BT_PHY_EDR_2M_5SLOT)
+		pkt_type &= ~HCI_2DH5;
+	else
+		pkt_type |= HCI_2DH5;
+
+	if (phys & BT_PHY_EDR_3M_1SLOT)
+		pkt_type &= ~HCI_3DH1;
+	else
+		pkt_type |= HCI_3DH1;
+
+	if (phys & BT_PHY_EDR_3M_3SLOT)
+		pkt_type &= ~HCI_3DH3;
+	else
+		pkt_type |= HCI_3DH3;
+
+	if (phys & BT_PHY_EDR_3M_5SLOT)
+		pkt_type &= ~HCI_3DH5;
+	else
+		pkt_type |= HCI_3DH5;
+
+	return pkt_type;
+}
+
+static int bt_phy_le_phy(u32 phys, u8 *tx_phys, u8 *rx_phys)
+{
+	if (!tx_phys || !rx_phys)
+		return -EINVAL;
+
+	*tx_phys = 0;
+	*rx_phys = 0;
+
+	if (phys & BT_PHY_LE_1M_TX)
+		*tx_phys |= HCI_LE_SET_PHY_1M;
+
+	if (phys & BT_PHY_LE_1M_RX)
+		*rx_phys |= HCI_LE_SET_PHY_1M;
+
+	if (phys & BT_PHY_LE_2M_TX)
+		*tx_phys |= HCI_LE_SET_PHY_2M;
+
+	if (phys & BT_PHY_LE_2M_RX)
+		*rx_phys |= HCI_LE_SET_PHY_2M;
+
+	if (phys & BT_PHY_LE_CODED_TX)
+		*tx_phys |= HCI_LE_SET_PHY_CODED;
+
+	if (phys & BT_PHY_LE_CODED_RX)
+		*rx_phys |= HCI_LE_SET_PHY_CODED;
+
+	return 0;
+}
+
+int hci_conn_set_phy(struct hci_conn *conn, u32 phys)
+{
+	u8 tx_phys, rx_phys;
+
+	switch (conn->type) {
+	case SCO_LINK:
+	case ESCO_LINK:
+		return -EINVAL;
+	case ACL_LINK:
+		/* Only allow setting BR/EDR PHYs if link type is ACL */
+		if (phys & ~BT_PHY_BREDR_MASK)
+			return -EINVAL;
+
+		return hci_acl_change_pkt_type(conn,
+					       bt_phy_pkt_type(conn, phys));
+	case LE_LINK:
+		/* Only allow setting LE PHYs if link type is LE */
+		if (phys & ~BT_PHY_LE_MASK)
+			return -EINVAL;
+
+		if (bt_phy_le_phy(phys, &tx_phys, &rx_phys))
+			return -EINVAL;
+
+		return hci_le_set_phy(conn, tx_phys, rx_phys);
+	default:
+		return -EINVAL;
+	}
+}
+
 static int abort_conn_sync(struct hci_dev *hdev, void *data)
 {
 	struct hci_conn *conn = data;
diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index 58075bf720554..467710a42d453 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -2869,6 +2869,31 @@ static void hci_cs_le_ext_create_conn(struct hci_dev *hdev, u8 status)
 	hci_dev_unlock(hdev);
 }
 
+static void hci_cs_le_set_phy(struct hci_dev *hdev, u8 status)
+{
+	struct hci_cp_le_set_phy *cp;
+	struct hci_conn *conn;
+
+	bt_dev_dbg(hdev, "status 0x%2.2x", status);
+
+	if (status)
+		return;
+
+	cp = hci_sent_cmd_data(hdev, HCI_OP_LE_SET_PHY);
+	if (!cp)
+		return;
+
+	hci_dev_lock(hdev);
+
+	conn = hci_conn_hash_lookup_handle(hdev, __le16_to_cpu(cp->handle));
+	if (conn) {
+		conn->le_tx_def_phys = cp->tx_phys;
+		conn->le_rx_def_phys = cp->rx_phys;
+	}
+
+	hci_dev_unlock(hdev);
+}
+
 static void hci_cs_le_read_remote_features(struct hci_dev *hdev, u8 status)
 {
 	struct hci_cp_le_read_remote_features *cp;
@@ -4359,6 +4384,7 @@ static const struct hci_cs {
 	HCI_CS(HCI_OP_LE_CREATE_CONN, hci_cs_le_create_conn),
 	HCI_CS(HCI_OP_LE_READ_REMOTE_FEATURES, hci_cs_le_read_remote_features),
 	HCI_CS(HCI_OP_LE_START_ENC, hci_cs_le_start_enc),
+	HCI_CS(HCI_OP_LE_SET_PHY, hci_cs_le_set_phy),
 	HCI_CS(HCI_OP_LE_EXT_CREATE_CONN, hci_cs_le_ext_create_conn),
 	HCI_CS(HCI_OP_LE_CREATE_CIS, hci_cs_le_create_cis),
 	HCI_CS(HCI_OP_LE_CREATE_BIG, hci_cs_le_create_big),
diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
index dd3f7bd98b1c6..ab0b68faa61c6 100644
--- a/net/bluetooth/hci_sync.c
+++ b/net/bluetooth/hci_sync.c
@@ -7447,3 +7447,75 @@ int hci_le_read_remote_features(struct hci_conn *conn)
 
 	return err;
 }
+
+static void pkt_type_changed(struct hci_dev *hdev, void *data, int err)
+{
+	struct hci_cp_change_conn_ptype *cp = data;
+
+	bt_dev_dbg(hdev, "err %d", err);
+
+	kfree(cp);
+}
+
+static int hci_change_conn_ptype_sync(struct hci_dev *hdev, void *data)
+{
+	struct hci_cp_change_conn_ptype *cp = data;
+
+	return __hci_cmd_sync_status_sk(hdev, HCI_OP_CHANGE_CONN_PTYPE,
+					sizeof(*cp), cp,
+					HCI_EV_PKT_TYPE_CHANGE,
+					HCI_CMD_TIMEOUT, NULL);
+}
+
+int hci_acl_change_pkt_type(struct hci_conn *conn, u16 pkt_type)
+{
+	struct hci_dev *hdev = conn->hdev;
+	struct hci_cp_change_conn_ptype *cp;
+
+	cp = kmalloc(sizeof(*cp), GFP_KERNEL);
+	if (!cp)
+		return -ENOMEM;
+
+	cp->handle = cpu_to_le16(conn->handle);
+	cp->pkt_type = cpu_to_le16(pkt_type);
+
+	return hci_cmd_sync_queue_once(hdev, hci_change_conn_ptype_sync, cp,
+				       pkt_type_changed);
+}
+
+static void le_phy_update_complete(struct hci_dev *hdev, void *data, int err)
+{
+	struct hci_cp_le_set_phy *cp = data;
+
+	bt_dev_dbg(hdev, "err %d", err);
+
+	kfree(cp);
+}
+
+static int hci_le_set_phy_sync(struct hci_dev *hdev, void *data)
+{
+	struct hci_cp_le_set_phy *cp = data;
+
+	return __hci_cmd_sync_status_sk(hdev, HCI_OP_LE_SET_PHY,
+					sizeof(*cp), cp,
+					HCI_EV_LE_PHY_UPDATE_COMPLETE,
+					HCI_CMD_TIMEOUT, NULL);
+}
+
+int hci_le_set_phy(struct hci_conn *conn, u8 tx_phys, u8 rx_phys)
+{
+	struct hci_dev *hdev = conn->hdev;
+	struct hci_cp_le_set_phy *cp;
+
+	cp = kmalloc(sizeof(*cp), GFP_KERNEL);
+	if (!cp)
+		return -ENOMEM;
+
+	memset(cp, 0, sizeof(*cp));
+	cp->handle = cpu_to_le16(conn->handle);
+	cp->tx_phys = tx_phys;
+	cp->rx_phys = rx_phys;
+
+	return hci_cmd_sync_queue_once(hdev, hci_le_set_phy_sync, cp,
+				       le_phy_update_complete);
+}
diff --git a/net/bluetooth/l2cap_sock.c b/net/bluetooth/l2cap_sock.c
index 9ee189c815d49..3ba3ce7eaa98a 100644
--- a/net/bluetooth/l2cap_sock.c
+++ b/net/bluetooth/l2cap_sock.c
@@ -885,7 +885,7 @@ static int l2cap_sock_setsockopt(struct socket *sock, int level, int optname,
 	struct bt_power pwr;
 	struct l2cap_conn *conn;
 	int err = 0;
-	u32 opt;
+	u32 opt, phys;
 	u16 mtu;
 	u8 mode;
 
@@ -1059,6 +1059,24 @@ static int l2cap_sock_setsockopt(struct socket *sock, int level, int optname,
 
 		break;
 
+	case BT_PHY:
+		if (sk->sk_state != BT_CONNECTED) {
+			err = -ENOTCONN;
+			break;
+		}
+
+		err = copy_safe_from_sockptr(&phys, sizeof(phys), optval,
+					     optlen);
+		if (err)
+			break;
+
+		if (!chan->conn)
+			break;
+
+		conn = chan->conn;
+		err = hci_conn_set_phy(conn->hcon, phys);
+		break;
+
 	case BT_MODE:
 		if (!enable_ecred) {
 			err = -ENOPROTOOPT;

From d6af4afb70c9b73ce344ec9b2414dab2c4dcd61f Mon Sep 17 00:00:00 2001
From: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Date: Tue, 6 Jan 2026 12:35:02 +0800
Subject: [PATCH 13/19] Bluetooth: btqca: move WCN7850 workaround to the caller

WCN7850 will first attempt to use ELF_TYPE_PATCH,
and if that fails, it will fall back to TLV_TYPE_PATCH.

To code uniformity, move WCN7850 workaround to the caller.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/btqca.c | 37 +++++++++++++++++--------------------
 1 file changed, 17 insertions(+), 20 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 7c958d6065bec..0af3e2109f310 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -581,28 +581,11 @@ static int qca_download_firmware(struct hci_dev *hdev,
 
 	ret = request_firmware(&fw, config->fwname, &hdev->dev);
 	if (ret) {
-		/* For WCN6750, if mbn file is not present then check for
-		 * tlv file.
-		 */
-		if (soc_type == QCA_WCN6750 && config->type == ELF_TYPE_PATCH) {
-			bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
-				   config->fwname, ret);
-			config->type = TLV_TYPE_PATCH;
-			snprintf(config->fwname, sizeof(config->fwname),
-				 "qca/msbtfw%02x.tlv", rom_ver);
-			bt_dev_info(hdev, "QCA Downloading %s", config->fwname);
-			ret = request_firmware(&fw, config->fwname, &hdev->dev);
-			if (ret) {
-				bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
-					   config->fwname, ret);
-				return ret;
-			}
-		}
 		/* If the board-specific file is missing, try loading the default
 		 * one, unless that was attempted already.
 		 */
-		else if (config->type == TLV_TYPE_NVM &&
-			 qca_get_alt_nvm_file(config->fwname, sizeof(config->fwname))) {
+		if (config->type == TLV_TYPE_NVM &&
+		    qca_get_alt_nvm_file(config->fwname, sizeof(config->fwname))) {
 			bt_dev_info(hdev, "QCA Downloading %s", config->fwname);
 			ret = request_firmware(&fw, config->fwname, &hdev->dev);
 			if (ret) {
@@ -861,8 +844,22 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	}
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	/* For WCN6750, if mbn file is not present then check for
+	 * tlv file.
+	 */
+	if (err < 0 && soc_type == QCA_WCN6750) {
+		bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
+			   config.fwname, err);
+		config.type = TLV_TYPE_PATCH;
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/msbtfw%02x.tlv", rom_ver);
+		bt_dev_info(hdev, "QCA Downloading %s", config.fwname);
+		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	}
+
 	if (err < 0) {
-		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
+		bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+			   config.fwname, err);
 		return err;
 	}
 

From 030d2c0e9c1d68e67f91c08704482ad9881583eb Mon Sep 17 00:00:00 2001
From: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Date: Tue, 6 Jan 2026 12:35:03 +0800
Subject: [PATCH 14/19] Bluetooth: btqca: Add WCN6855 firmware priority
 selection feature

Historically, WCN685x and QCA2066 shared the same firmware files.
Now, changes are planned for the firmware that will make it incompatible
with QCA2066, so a new firmware name is required for WCN685x.

Test Steps:
 - Boot device
 - Check the BTFW loading status via dmesg

Sanity pass and Test Log:
QCA Downloading qca/wcnhpbftfw21.tlv
Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
QCA Downloading qca/hpbftfw21.tlv

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/btqca.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 0af3e2109f310..74f820e89655e 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -830,8 +830,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 				 "qca/msbtfw%02x.mbn", rom_ver);
 			break;
 		case QCA_WCN6855:
+			/* Due to historical reasons, WCN685x chip has been using firmware
+			 * without the "wcn" prefix. The mapping between the chip and its
+			 * corresponding firmware has now been corrected.
+			 */
 			snprintf(config.fwname, sizeof(config.fwname),
-				 "qca/hpbtfw%02x.tlv", rom_ver);
+				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
 			break;
 		case QCA_WCN7850:
 			snprintf(config.fwname, sizeof(config.fwname),
@@ -855,6 +859,10 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 			 "qca/msbtfw%02x.tlv", rom_ver);
 		bt_dev_info(hdev, "QCA Downloading %s", config.fwname);
 		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	} else if (err < 0 && !rampatch_name && soc_type == QCA_WCN6855) {
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/hpbtfw%02x.tlv", rom_ver);
+		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
 	}
 
 	if (err < 0) {
@@ -920,7 +928,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		case QCA_WCN6855:
 			qca_read_fw_board_id(hdev, &boardid);
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
-						  "hpnv", soc_type, ver, rom_ver, boardid);
+						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
 			break;
 		case QCA_WCN7850:
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
@@ -933,8 +941,15 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	}
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	if (err < 0 && !firmware_name && soc_type == QCA_WCN6855) {
+		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
+					  "hpnv", soc_type, ver, rom_ver, boardid);
+		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	}
+
 	if (err < 0) {
-		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
+		bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+			   config.fwname, err);
 		return err;
 	}
 

From 6538549c619d915e35142f49e3bb1e2dfc7a7f3c Mon Sep 17 00:00:00 2001
From: Techie Ernie <techieernie@gmail.com>
Date: Wed, 24 Dec 2025 11:31:29 +0800
Subject: [PATCH 15/19] Bluetooth: btusb: Add USB ID 0489:e112 for Realtek
 8851BE

Add USB ID 0489:e112 for the Realtek 8851BE Bluetooth adapter.
Without this entry, the device is not handled correctly by btusb and Bluetooth fails to initialise.
Adding the ID enables proper Realtek initialization for Bluetooth to work on various motherboards using this Bluetooth adapter.

The device identifies as:
  Bus 001 Device XXX: ID 0489:e112 Foxconn / Hon Hai Bluetooth Radio

Tested on Realtek 8851BE. Bluetooth works after this change is made.

Signed-off-by: Techie Ernie <techieernie@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 646de80c7e7be..de9e484efef71 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -521,6 +521,8 @@ static const struct usb_device_id quirks_table[] = {
 	{ USB_DEVICE(0x0bda, 0xb850), .driver_info = BTUSB_REALTEK },
 	{ USB_DEVICE(0x13d3, 0x3600), .driver_info = BTUSB_REALTEK },
 	{ USB_DEVICE(0x13d3, 0x3601), .driver_info = BTUSB_REALTEK },
+	{ USB_DEVICE(0x0489, 0xe112), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
 
 	/* Realtek 8851BU Bluetooth devices */
 	{ USB_DEVICE(0x3625, 0x010b), .driver_info = BTUSB_REALTEK |

From d4f7cb6e2df7b63af740d5848c74ad1d9d157033 Mon Sep 17 00:00:00 2001
From: Yang Li <yang.li@amlogic.com>
Date: Fri, 19 Dec 2025 10:43:09 +0800
Subject: [PATCH 16/19] Bluetooth: hci_sync: enable PA Sync Lost event

Enable the PA Sync Lost event mask to ensure PA sync loss is properly
reported and handled.

Fixes: 485e0626e587 ("Bluetooth: hci_event: Fix not handling PA Sync Lost event")
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 net/bluetooth/hci_sync.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
index ab0b68faa61c6..0e6660ddc00a7 100644
--- a/net/bluetooth/hci_sync.c
+++ b/net/bluetooth/hci_sync.c
@@ -4420,6 +4420,7 @@ static int hci_le_set_event_mask_sync(struct hci_dev *hdev)
 	if (bis_capable(hdev)) {
 		events[1] |= 0x20;	/* LE PA Report */
 		events[1] |= 0x40;	/* LE PA Sync Established */
+		events[1] |= 0x80;	/* LE PA Sync Lost */
 		events[3] |= 0x04;	/* LE Create BIG Complete */
 		events[3] |= 0x08;	/* LE Terminate BIG Complete */
 		events[3] |= 0x10;	/* LE BIG Sync Established */

From bdb9aba465a85122bcba01a6154e237b9843e25b Mon Sep 17 00:00:00 2001
From: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Date: Mon, 22 Dec 2025 14:36:45 -0500
Subject: [PATCH 17/19] Bluetooth: Fix using PHYs bitfields as PHY value

This renames the PHY fields in bt_iso_io_qos to PHYs (plural) since it
represents a bitfield where multiple PHYs can be set and make the same
change also to HCI_OP_LE_SET_CIG_PARAMS since both c_phy and p_phy
fields are bitfields.

This also fixes the assumption that hci_evt_le_cis_established PHYs
fields are compatible with bt_iso_io_qos, they are not, the fields in
hci_evt_le_cis_established represent just a single PHY value so they
need to be converted to bitfield when set in bt_iso_io_qos.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
---
 include/net/bluetooth/bluetooth.h |  8 +++----
 include/net/bluetooth/hci.h       |  6 +++---
 net/bluetooth/hci_conn.c          | 35 ++++++++++++++++---------------
 net/bluetooth/hci_event.c         | 23 ++++++++++++++++----
 net/bluetooth/hci_sync.c          |  6 +++---
 net/bluetooth/iso.c               | 10 ++++-----
 6 files changed, 52 insertions(+), 36 deletions(-)

diff --git a/include/net/bluetooth/bluetooth.h b/include/net/bluetooth/bluetooth.h
index 89a60919050b0..69eed69f7f265 100644
--- a/include/net/bluetooth/bluetooth.h
+++ b/include/net/bluetooth/bluetooth.h
@@ -182,7 +182,7 @@ struct bt_iso_io_qos {
 	__u32 interval;
 	__u16 latency;
 	__u16 sdu;
-	__u8  phy;
+	__u8  phys;
 	__u8  rtn;
 };
 
@@ -221,9 +221,9 @@ struct bt_iso_qos {
 	};
 };
 
-#define BT_ISO_PHY_1M		0x01
-#define BT_ISO_PHY_2M		0x02
-#define BT_ISO_PHY_CODED	0x04
+#define BT_ISO_PHY_1M		BIT(0)
+#define BT_ISO_PHY_2M		BIT(1)
+#define BT_ISO_PHY_CODED	BIT(2)
 #define BT_ISO_PHY_ANY		(BT_ISO_PHY_1M | BT_ISO_PHY_2M | \
 				 BT_ISO_PHY_CODED)
 
diff --git a/include/net/bluetooth/hci.h b/include/net/bluetooth/hci.h
index db76c2d1eeaa1..89ad9470fa71b 100644
--- a/include/net/bluetooth/hci.h
+++ b/include/net/bluetooth/hci.h
@@ -1891,7 +1891,7 @@ struct hci_cp_le_set_phy {
 	__u8    all_phys;
 	__u8    tx_phys;
 	__u8    rx_phys;
-	__le16   phy_opts;
+	__le16  phy_opts;
 } __packed;
 
 #define HCI_OP_LE_SET_EXT_SCAN_PARAMS   0x2041
@@ -2147,8 +2147,8 @@ struct hci_cis_params {
 	__u8    cis_id;
 	__le16  c_sdu;
 	__le16  p_sdu;
-	__u8    c_phy;
-	__u8    p_phy;
+	__u8    c_phys;
+	__u8    p_phys;
 	__u8    c_rtn;
 	__u8    p_rtn;
 } __packed;
diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
index 1a4b6badf2b35..0795818963a52 100644
--- a/net/bluetooth/hci_conn.c
+++ b/net/bluetooth/hci_conn.c
@@ -1825,7 +1825,7 @@ static int hci_le_create_big(struct hci_conn *conn, struct bt_iso_qos *qos)
 	cp.bis.sdu = cpu_to_le16(qos->bcast.out.sdu);
 	cp.bis.latency =  cpu_to_le16(qos->bcast.out.latency);
 	cp.bis.rtn  = qos->bcast.out.rtn;
-	cp.bis.phy  = qos->bcast.out.phy;
+	cp.bis.phy  = qos->bcast.out.phys;
 	cp.bis.packing = qos->bcast.packing;
 	cp.bis.framing = qos->bcast.framing;
 	cp.bis.encryption = qos->bcast.encryption;
@@ -1875,10 +1875,10 @@ static int set_cig_params_sync(struct hci_dev *hdev, void *data)
 		cis->cis_id = cis_id;
 		cis->c_sdu  = cpu_to_le16(conn->iso_qos.ucast.out.sdu);
 		cis->p_sdu  = cpu_to_le16(conn->iso_qos.ucast.in.sdu);
-		cis->c_phy  = qos->ucast.out.phy ? qos->ucast.out.phy :
-			      qos->ucast.in.phy;
-		cis->p_phy  = qos->ucast.in.phy ? qos->ucast.in.phy :
-			      qos->ucast.out.phy;
+		cis->c_phys = qos->ucast.out.phys ? qos->ucast.out.phys :
+			      qos->ucast.in.phys;
+		cis->p_phys = qos->ucast.in.phys ? qos->ucast.in.phys :
+			      qos->ucast.out.phys;
 		cis->c_rtn  = qos->ucast.out.rtn;
 		cis->p_rtn  = qos->ucast.in.rtn;
 	}
@@ -1980,8 +1980,8 @@ struct hci_conn *hci_bind_cis(struct hci_dev *hdev, bdaddr_t *dst,
 		return cis;
 
 	/* Update LINK PHYs according to QoS preference */
-	cis->le_tx_phy = qos->ucast.out.phy;
-	cis->le_rx_phy = qos->ucast.in.phy;
+	cis->le_tx_phy = qos->ucast.out.phys;
+	cis->le_rx_phy = qos->ucast.in.phys;
 
 	/* If output interval is not set use the input interval as it cannot be
 	 * 0x000000.
@@ -2096,15 +2096,15 @@ int hci_le_create_cis_pending(struct hci_dev *hdev)
 }
 
 static void hci_iso_qos_setup(struct hci_dev *hdev, struct hci_conn *conn,
-			      struct bt_iso_io_qos *qos, __u8 phy)
+			      struct bt_iso_io_qos *qos, __u8 phys)
 {
 	/* Only set MTU if PHY is enabled */
-	if (!qos->sdu && qos->phy)
+	if (!qos->sdu && qos->phys)
 		qos->sdu = conn->mtu;
 
 	/* Use the same PHY as ACL if set to any */
-	if (qos->phy == BT_ISO_PHY_ANY)
-		qos->phy = phy;
+	if (qos->phys == BT_ISO_PHY_ANY)
+		qos->phys = phys;
 
 	/* Use LE ACL connection interval if not set */
 	if (!qos->interval)
@@ -2124,7 +2124,7 @@ static int create_big_sync(struct hci_dev *hdev, void *data)
 	u32 flags = 0;
 	int err;
 
-	if (qos->bcast.out.phy == 0x02)
+	if (qos->bcast.out.phys == BIT(1))
 		flags |= MGMT_ADV_FLAG_SEC_2M;
 
 	/* Align intervals */
@@ -2233,8 +2233,7 @@ struct hci_conn *hci_bind_bis(struct hci_dev *hdev, bdaddr_t *dst, __u8 sid,
 		return conn;
 
 	/* Update LINK PHYs according to QoS preference */
-	conn->le_tx_phy = qos->bcast.out.phy;
-	conn->le_tx_phy = qos->bcast.out.phy;
+	conn->le_tx_def_phys = qos->bcast.out.phys;
 
 	/* Add Basic Announcement into Peridic Adv Data if BASE is set */
 	if (base_len && base) {
@@ -2243,7 +2242,7 @@ struct hci_conn *hci_bind_bis(struct hci_dev *hdev, bdaddr_t *dst, __u8 sid,
 	}
 
 	hci_iso_qos_setup(hdev, conn, &qos->bcast.out,
-			  conn->le_tx_phy ? conn->le_tx_phy :
+			  conn->le_tx_def_phys ? conn->le_tx_def_phys :
 			  hdev->le_tx_def_phys);
 
 	conn->iso_qos = *qos;
@@ -2363,9 +2362,11 @@ struct hci_conn *hci_connect_cis(struct hci_dev *hdev, bdaddr_t *dst,
 		return le;
 
 	hci_iso_qos_setup(hdev, le, &qos->ucast.out,
-			  le->le_tx_phy ? le->le_tx_phy : hdev->le_tx_def_phys);
+			  le->le_tx_def_phys ? le->le_tx_def_phys :
+			  hdev->le_tx_def_phys);
 	hci_iso_qos_setup(hdev, le, &qos->ucast.in,
-			  le->le_rx_phy ? le->le_rx_phy : hdev->le_rx_def_phys);
+			  le->le_rx_def_phys ? le->le_rx_def_phys :
+			  hdev->le_rx_def_phys);
 
 	cis = hci_bind_cis(hdev, dst, dst_type, qos, timeout);
 	if (IS_ERR(cis)) {
diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index 467710a42d453..286529d2e554a 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -6867,6 +6867,21 @@ static void hci_le_phy_update_evt(struct hci_dev *hdev, void *data,
 	hci_dev_unlock(hdev);
 }
 
+/* Convert LE PHY to QoS PHYs */
+static u8 le_phy_qos(u8 phy)
+{
+	switch (phy) {
+	case 0x01:
+		return HCI_LE_SET_PHY_1M;
+	case 0x02:
+		return HCI_LE_SET_PHY_2M;
+	case 0x03:
+		return HCI_LE_SET_PHY_CODED;
+	}
+
+	return 0;
+}
+
 static void hci_le_cis_established_evt(struct hci_dev *hdev, void *data,
 				       struct sk_buff *skb)
 {
@@ -6928,8 +6943,8 @@ static void hci_le_cis_established_evt(struct hci_dev *hdev, void *data,
 					  1000);
 		qos->ucast.in.sdu = ev->c_bn ? le16_to_cpu(ev->c_mtu) : 0;
 		qos->ucast.out.sdu = ev->p_bn ? le16_to_cpu(ev->p_mtu) : 0;
-		qos->ucast.in.phy = ev->c_phy;
-		qos->ucast.out.phy = ev->p_phy;
+		qos->ucast.in.phys = le_phy_qos(ev->c_phy);
+		qos->ucast.out.phys = le_phy_qos(ev->p_phy);
 		break;
 	case HCI_ROLE_MASTER:
 		qos->ucast.in.interval = p_sdu_interval;
@@ -6943,8 +6958,8 @@ static void hci_le_cis_established_evt(struct hci_dev *hdev, void *data,
 					  1000);
 		qos->ucast.out.sdu = ev->c_bn ? le16_to_cpu(ev->c_mtu) : 0;
 		qos->ucast.in.sdu = ev->p_bn ? le16_to_cpu(ev->p_mtu) : 0;
-		qos->ucast.out.phy = ev->c_phy;
-		qos->ucast.in.phy = ev->p_phy;
+		qos->ucast.out.phys = le_phy_qos(ev->c_phy);
+		qos->ucast.in.phys = le_phy_qos(ev->p_phy);
 		break;
 	}
 
diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
index 0e6660ddc00a7..f04a90bce4a94 100644
--- a/net/bluetooth/hci_sync.c
+++ b/net/bluetooth/hci_sync.c
@@ -2948,8 +2948,8 @@ static int hci_le_set_ext_scan_param_sync(struct hci_dev *hdev, u8 type,
 			if (conn) {
 				struct bt_iso_qos *qos = &conn->iso_qos;
 
-				if (qos->bcast.in.phy & BT_ISO_PHY_1M ||
-				    qos->bcast.in.phy & BT_ISO_PHY_2M) {
+				if (qos->bcast.in.phys & BT_ISO_PHY_1M ||
+				    qos->bcast.in.phys & BT_ISO_PHY_2M) {
 					cp->scanning_phys |= LE_SCAN_PHY_1M;
 					hci_le_scan_phy_params(phy, type,
 							       interval,
@@ -2958,7 +2958,7 @@ static int hci_le_set_ext_scan_param_sync(struct hci_dev *hdev, u8 type,
 					phy++;
 				}
 
-				if (qos->bcast.in.phy & BT_ISO_PHY_CODED) {
+				if (qos->bcast.in.phys & BT_ISO_PHY_CODED) {
 					cp->scanning_phys |= LE_SCAN_PHY_CODED;
 					hci_le_scan_phy_params(phy, type,
 							       interval * 3,
diff --git a/net/bluetooth/iso.c b/net/bluetooth/iso.c
index e36d24a9098b9..1459ab161fd2a 100644
--- a/net/bluetooth/iso.c
+++ b/net/bluetooth/iso.c
@@ -361,7 +361,7 @@ static int iso_connect_bis(struct sock *sk)
 	}
 
 	/* Fail if out PHYs are marked as disabled */
-	if (!iso_pi(sk)->qos.bcast.out.phy) {
+	if (!iso_pi(sk)->qos.bcast.out.phys) {
 		err = -EINVAL;
 		goto unlock;
 	}
@@ -458,7 +458,7 @@ static int iso_connect_cis(struct sock *sk)
 	}
 
 	/* Fail if either PHYs are marked as disabled */
-	if (!iso_pi(sk)->qos.ucast.in.phy && !iso_pi(sk)->qos.ucast.out.phy) {
+	if (!iso_pi(sk)->qos.ucast.in.phys && !iso_pi(sk)->qos.ucast.out.phys) {
 		err = -EINVAL;
 		goto unlock;
 	}
@@ -894,7 +894,7 @@ static struct proto iso_proto = {
 	.interval	= 10000u, \
 	.latency	= 10u, \
 	.sdu		= 40u, \
-	.phy		= BT_ISO_PHY_2M, \
+	.phys		= BT_ISO_PHY_2M, \
 	.rtn		= 2u, \
 }
 
@@ -1661,7 +1661,7 @@ static int iso_sock_recvmsg(struct socket *sock, struct msghdr *msg,
 static bool check_io_qos(struct bt_iso_io_qos *qos)
 {
 	/* If no PHY is enable SDU must be 0 */
-	if (!qos->phy && qos->sdu)
+	if (!qos->phys && qos->sdu)
 		return false;
 
 	if (qos->interval && (qos->interval < 0xff || qos->interval > 0xfffff))
@@ -1670,7 +1670,7 @@ static bool check_io_qos(struct bt_iso_io_qos *qos)
 	if (qos->latency && (qos->latency < 0x05 || qos->latency > 0xfa0))
 		return false;
 
-	if (qos->phy > BT_ISO_PHY_ANY)
+	if (qos->phys > BT_ISO_PHY_ANY)
 		return false;
 
 	return true;

From de288ca0b88a97be8f78ca83dacf9c9994076c23 Mon Sep 17 00:00:00 2001
From: Tedd Ho-Jeong An <tedd.an@intel.com>
Date: Wed, 4 Nov 2020 21:09:48 -0800
Subject: [PATCH 18/19] workflow: Add workflow files for ci

This patch adds workflow files for ci:

[sync.yml]
 - The workflow file for scheduled work
 - Sync the repo with upstream repo and rebase the workflow branch
 - Review the patches in the patchwork and creates the PR if needed

[ci.yml]
 - The workflow file for CI tasks
 - Run CI tests when PR is created

Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
---
 .github/workflows/ci.yml   | 25 ++++++++++++++++++++++
 .github/workflows/sync.yml | 43 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 68 insertions(+)
 create mode 100644 .github/workflows/ci.yml
 create mode 100644 .github/workflows/sync.yml

diff --git a/.github/workflows/ci.yml b/.github/workflows/ci.yml
new file mode 100644
index 0000000000000..3a2c45c37553c
--- /dev/null
+++ b/.github/workflows/ci.yml
@@ -0,0 +1,25 @@
+name: CI
+
+on: [pull_request]
+
+jobs:
+  ci:
+    runs-on: ubuntu-latest
+    name: CI for Pull Request
+    steps:
+    - name: Checkout the source code
+      uses: actions/checkout@v3
+      with:
+        path: src/src
+
+    - name: CI
+      uses: tedd-an/bzcafe@main
+      with:
+        task: ci
+        base_folder: src
+        space: kernel
+        github_token: ${{ secrets.GITHUB_TOKEN }}
+        email_token: ${{ secrets.EMAIL_TOKEN }}
+        patchwork_token: ${{ secrets.PATCHWORK_TOKEN }}
+        patchwork_user: ${{ secrets.PATCHWORK_USER }}
+
diff --git a/.github/workflows/sync.yml b/.github/workflows/sync.yml
new file mode 100644
index 0000000000000..3883d55a23267
--- /dev/null
+++ b/.github/workflows/sync.yml
@@ -0,0 +1,43 @@
+name: Sync
+
+on:
+  schedule:
+  - cron: "*/30 * * * *"
+
+jobs:
+  sync_repo:
+    runs-on: ubuntu-latest
+    steps:
+    - uses: actions/checkout@v3
+      with:
+        ref: master
+
+    - name: Sync Repo
+      uses: tedd-an/bzcafe@main
+      with:
+        task: sync
+        upstream_repo: 'https://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next.git'
+        github_token: ${{ secrets.GITHUB_TOKEN }}
+
+    - name: Cleanup PR
+      uses: tedd-an/bzcafe@main
+      with:
+        task: cleanup
+        github_token: ${{ secrets.ACTION_TOKEN }}
+
+  sync_patchwork:
+    needs: sync_repo
+    runs-on: ubuntu-latest
+    steps:
+    - uses: actions/checkout@v3
+
+    - name: Sync Patchwork
+      uses: tedd-an/bzcafe@main
+      with:
+        task: patchwork
+        space: kernel
+        github_token: ${{ secrets.ACTION_TOKEN }}
+        email_token: ${{ secrets.EMAIL_TOKEN }}
+        patchwork_token: ${{ secrets.PATCHWORK_TOKEN }}
+        patchwork_user: ${{ secrets.PATCHWORK_USER }}
+

From 2d8627a622121ea842979574e4e0c315e0b4f6ae Mon Sep 17 00:00:00 2001
From: Yang Li <yang.li@amlogic.com>
Date: Thu, 8 Jan 2026 14:03:43 +0800
Subject: [PATCH 19/19] Bluetooth: hci_sync: use HCI_CMD_TIMEOUT for PA sync
 commands

PA sync HCI commands incorrectly use conn->conn_timeout, which defaults
to 20s and is too long. If the PA Sync Established event is not
received, the command remains pending and causes userspace timeouts.

Signed-off-by: Yang Li <yang.li@amlogic.com>
---
 net/bluetooth/hci_sync.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
index f04a90bce4a94..58292b01f0624 100644
--- a/net/bluetooth/hci_sync.c
+++ b/net/bluetooth/hci_sync.c
@@ -7159,7 +7159,7 @@ static int hci_le_pa_create_sync(struct hci_dev *hdev, void *data)
 	if (conn->sid == HCI_SID_INVALID) {
 		err = __hci_cmd_sync_status_sk(hdev, HCI_OP_NOP, 0, NULL,
 					       HCI_EV_LE_EXT_ADV_REPORT,
-					       conn->conn_timeout, NULL);
+					       HCI_CMD_TIMEOUT, NULL);
 		if (err == -ETIMEDOUT)
 			goto done;
 	}
@@ -7187,7 +7187,7 @@ static int hci_le_pa_create_sync(struct hci_dev *hdev, void *data)
 	err = __hci_cmd_sync_status_sk(hdev, HCI_OP_LE_PA_CREATE_SYNC,
 				       sizeof(cp), &cp,
 				       HCI_EV_LE_PA_SYNC_ESTABLISHED,
-				       conn->conn_timeout, NULL);
+				       HCI_CMD_TIMEOUT, NULL);
 	if (err == -ETIMEDOUT)
 		__hci_cmd_sync_status(hdev, HCI_OP_LE_PA_CREATE_SYNC_CANCEL,
 				      0, NULL, HCI_CMD_TIMEOUT);