wifiScan参数设置中增加说明展锐平台不支持scan_timeout和priority

Author: Jayceon Fu(付俊臣)

en-us/api/QuecPythonClasslib.md

@@ -7792,8 +7792,8 @@ True
   | timeout       | Integer type | This parameter is the timeout of upper layer application. When the application triggers timeout, it actively reports the scanned hot spot information. The application automatically reports the hot spot information if it scans all the hop spots which have been set previously or the underlying layer scan reaches the frequency sweeping timeout before the timeout of the application. <br>Range:<br/>600S: 4–255; unit: s.<br/>200U/600U: 120–5000; unit: ms. |
   | round         | Integer type | This parameter is the scanning rounds of wifi. When reaching the scanning rounds, the scan stops and the scanning results are obtained. <br/>Range:<br/>600S: 1–3; unit: round<br/>200U/600U: 1–10; unit: round |
   | max_bssid_num | Integer type | This parameter determines the maximum number of hot spots to be scanned. If the number of hot spots scanned by the underlying layer reaches the maximum, the scan stops and the scanning results are obtained. <br/>Range:<br/>600S: 4–30<br/>200U/600U: 1–300 |
-  | scan_timeout  | Integer type | This parameter is the wifi hot spot scanning timeout of underlying layer. If the underlying layer scan reaches the hot spot scanning timeout set previously,  the scan stops and the scanning results are obtained. Range: 1–255. Unit: second. |
-  | priority      | Integer type | This parameter is the priority setting of wifi scanning service. 0 indicates that ps is preferred; 1 indicates that wifi is preferred. When ps is preferred, the wifi scan is terminated when a data service is initiated. When wifi is preferred, RRC connection is not connected when a data service is initiated. wifi scan runs normally. The RRC connection is only established after the scan completes. |
+  | scan_timeout  | Integer type | This parameter is the wifi hot spot scanning timeout of underlying layer. If the underlying layer scan reaches the hot spot scanning timeout set previously,  the scan stops and the scanning results are obtained. Range: 1–255. Unit: second. 200U or 600U platforms do not support this parameter. You can set this parameter to 0. |
+  | priority      | Integer type | This parameter is the priority setting of wifi scanning service. 0 indicates that ps is preferred; 1 indicates that wifi is preferred. When ps is preferred, the wifi scan is terminated when a data service is initiated. When wifi is preferred, RRC connection is not connected when a data service is initiated. wifi scan runs normally. The RRC connection is only established after the scan completes. 200U or 600U platforms do not support this parameter. You can set this parameter to 0. |
 
 * Return Value：
 

zh-cn/api/QuecPythonClasslib.md

@@ -4729,7 +4729,7 @@ while 1:
 | 2    | 按 RESET 重启                    |
 | 3    | VBAT 触发的开机                  |
 | 4    | RTC 定时开机                     |
-| 5    | watchdog 触发重启（或异常开机）  |
+| 5    | watchdog 触发重启或异常开机      |
 | 6    | VBUS 触发的开机                  |
 | 7    | 充电开机                         |
 | 8    | PSM 唤醒开机                     |
@@ -7822,8 +7822,8 @@ True
   | timeout       | 整型 | 该超时时间参数是上层应用的超时，当触发超时会主动上报已扫描到的热点信息，若在超时前扫描到设置的热点个数或达到底层扫频超时时间会自动上报热点信息。<br>参数范围：<br/>600S ：4-255秒<br/>200U/600U ：120-5000毫秒 |
   | round         | 整型 | 该参数是wifi扫描轮，达到扫描轮数后，会结束扫描并获取扫描结果。<br/>参数范围：<br/>600S ：1-3轮次<br/>200U/600U ：1-10轮次 |
   | max_bssid_num | 整型 | 该参数是wifi扫描热点最大个，若底层扫描热点个数达到设置的最大个数，会结束扫描并获取扫描结果。<br/>参数范围：<br/>600S ：4-30个<br/>200U/600U ：1-300个 |
-  | scan_timeout  | 整型 | 该参数是底层wifi扫描热点超时时间，若底层扫描热点时间达到设置的超时时间，会结束扫描并获取扫描结果。该参数设置范围为1-255秒。 |
-  | priority      | 整型 | 该参数是wifi扫描业务优先级设置，0为ps优先，1为wifi优先。ps优先时，当有数据业务发起时会中断wifi扫描。Wifi优先时，当有数据业务发起时，不会建立RRC连接，保障wifi扫描正常执行，扫描结束后才会建立RRC连接。 |
+  | scan_timeout  | 整型 | 该参数是底层wifi扫描热点超时时间，若底层扫描热点时间达到设置的超时时间，会结束扫描并获取扫描结果。该参数设置范围为1-255秒。200U/600U 平台不支持该参数，设置时写0即可。 |
+  | priority      | 整型 | 该参数是wifi扫描业务优先级设置，0为ps优先，1为wifi优先。ps优先时，当有数据业务发起时会中断wifi扫描。Wifi优先时，当有数据业务发起时，不会建立RRC连接，保障wifi扫描正常执行，扫描结束后才会建立RRC连接。200U/600U 平台不支持该参数，设置时写0即可。 |
 
 * 返回值：